1) Follow the instructions for use
2) Storage temperature
3) Humidity of storage conditions
4) Expiry date (yyyy=year,mm=month)
WEARER INFORMATION
WARNINGS Read and understand before use
1. A properly selected filtering half masks is essential to protect your health. Before using this product consult a safety professional to determine its suitability for your intended application.
2. As with any respiratory device, the wearer MUST be adequately trained prior to use, Before use, the wearer should always check the mask is in good condition -not dirt, no damage to head strap attachment etc.
3. This product does not protect the wearer against gasses, vapors or mist whose liquids produce harmful vapors or gases
4. Do not use in sandblasting operations.
5. This product does not supply oxygen. Use this filtering half masks only in well-ventilated areas containing sufficient oxygen (at least 19.5%) to support life.
6. Do not use when contaminant and the concentration are unknown or immediately dangerous to life and health.
7. Leave work area immediately if: a) breathing becomes difficult, b) dizziness or other distress, c) the filtering half masks becomes damaged or d )an emergency occurs.
8. if user has any illness or discomfort, consult a licensed medical doctor to determine suitability of use
9. Facial hair and certain facial characteristics will prohibit effective use of this product.
10. Replace a filtering half masks when the breathing resistance become excessive due to dust loading or after a maximum of 8-hours continuous usage,"single shift use"
11. Failure to observe all warnings and instructions on the use of this filtering half masks may result in serious illness or permanent injury.
12. The equipment should not act as an ignition source but it should not be used in explosive atmospheres as the concentration of contaminants within normal flammability range would exceed the limit sin the selection guide.
13. Store filtering half masks in a sealed container away from contaminated areas when not in use.
14. Store filter in a half masks in the original packing during transport.
15. Please make sure the masks fit properly before entering working environment.
LIMITED WARRANTY
IMPORTANT NOTICE TO PURCHASER:
This limited warranty is made in aspect to the warranties of merchantability, fitness for particular purposes and all other warranties, express or implied. There are no other warranties which extend beyond the description on the face hereof. The physical standards and specifications of Safety Jogger will be met by products sold. Exclusive Remedies: damages for the breach of this limited warranty are limited to the replacement of such quantity of Safety Jogger, products proved to be defectively manufactured. Except as provided above, Safety logger shall not be
Liable or responsible for any loss, damage, or liability, direct,indirect,incidental, special, or consequential, arising out of sale, use, or misuse, or the inability to use products by users.
PARTICULATE FILTERING HALF MASKS
This filtering half masks is designed for applications involving fine non-toxic dust and fibers. This filtering half masks meets the requirements of EN 149(FFP2 NR, FFP3 NR) and should be used to protect the wearer from solid and water-based aerosols only. The filtering half masks can be used in concentrations of contaminate up to 10 times the Occupational Exposure Limits (OEL)
SERVICE TIME LIMITATION
1. Do not use the same filtering half masks for more than 8 hours, continuous or intermittent, in dirty workplaces that could result in high- Iter loading.
2. 2Leave contaminated area and remove filtering half masks if breathing becomes difficult or proper ft cannot be obtained or the filtering halt masks is damaged,soiled, or distorted.Do not use the same filtering half masks again once it has been used in contaminated area.
STEP 1
Hold the filtering half masks in hand with the nosepiece at your fingertips, allowing the headbands to hang freely below your hand.
STEP 2+3
Stretch and position the top band high on the back of the head. Stretch the bottom band over the head and position below your ears
STEP 4
Using both hands, mold nosepiece to the shape of your nose
STEP 5+6
To test fitting: a) Cup both hands over the filtering half masks being careful not to disturb position, and b)inhale vigorously. f air leaks around the edges.reposition the straps or adjust strap tension for better fit. f there are still noticeable leaks then this mask may not be suitable for you and we advise you to seek another style from our range